How to Repair Rattan Garden Furniture

Last Updated: January 19, 2024 References

Rattan garden furniture adds a simple but elegant, woven touch to your outdoor living space. While this furniture is pretty low-maintenance, the woven material can unravel or break over time. Not to worry—both wooden and synthetic rattan are easy to repair, and both can be fixed in the same way. If your furniture only has a few loose ends or wrappings, refer to the first method in this guide. If some sections of your furniture need a little extra TLC, skip ahead to the second method.

Method 1

Method 1 of 2:

Loose Ends and Wrappings

Grab a bristled brush and clean off any dirty sections of your furniture. Focus especially on any sections you’ll be fixing up, so your repairs look clean and seamless.^{[1]
X
Research source}
2
Wipe down real, wooden rattan furniture with dish soap and water. Stir ¹⁄₄ c (59 mL) of dishwashing soap with 1 US gal (3.8 L) of water.^{[2]
X
Research source} Then, dip a soft rag into the sudsy mixture and wipe down the entire surface of the furniture. Clean any hard-to-reach crevices with a toothbrush.^{[3]
X
Research source}
- Don’t get your rag sopping wet—if you get your rattan furniture too wet, you might damage it.
Advertisement
Sometimes, loose rattan weaving looks warped, creating “holes” in your furniture. Locate the specific strands of rattan material that look loose and warped. Then, slide the end of a flathead screwdriver beneath the end of the strand. Lift up the strands with the screwdriver—this will tighten the material, completely removing the “hole.”^{[4]
X
Research source}
4
Secure any loose ends back into place with super glue. After a lot of use and time outside, rattan ends can look a little worse for wear. Not to worry—simply squeeze a dot of super glue along each end, and tuck them back into the weaving. Then, wait for the glue to dry and seal before using the furniture again.
- Check the glue label as well—certain types of glue might need more time to dry and cure before you sit on or use the furniture again.
Rattan furniture stays in place via tight “wrappings” along the edges of the furniture. If one of these wrappings gets loose, it could throw the whole weave pattern out of whack. Pull these loose sections taut and wrap them back around the side of your furniture. Then, secure them in place with super glue.

Method 2

Method 2 of 2:

Damaged or Broken Strands

Take a close look at your rattan furniture and pinpoint where the broken or damaged strands are. Then, grab a pair of pliers or scissors and make 2 cuts—1 on either end of the damaged rattan strand. Cut out most of the strand, leaving only ¹⁄₂ in (1.3 cm) of slack on either side of the weaving.^{[5]
X
Research source}
2
Measure and cut a new replacement strand for your furniture. Place the new rattan strand next to the rattan strand that you just cut out and removed. Then, unwind and cut a length of new rattan that’s a little longer than the damaged section, so you have plenty of material to work with in your repairs.^{[6]
X
Research source}
- If the new section is too long, you can always trim it down later.
- You can purchase replacement rattan material online, or at specialty stores.
3
Soak the replacement rattan strands in water for 30 minutes. Fill a large bowl with water and submerge your rattan strands. Set a timer for 30 minutes—this makes the rattan material nice and flexible, and makes it a lot easier to work with during your repairs. Before continuing with the repairs, blot away any excess water from the rattan material.
- The water doesn’t have to be a specific temperature! Any type of water helps make the material more pliable.
4
Apply a dot of super glue along 1 end of the rattan strand. Spread the glue along the bottom end of the material, so it will hold in place.^{[7]
X
Research source}
- Waterproof super glue works best for outdoor furniture.
5
Press the glued end of the rattan strand in place for 5 minutes. Find the trimmed end of rattan, where you cut away the damaged section of material. Press the glued section of rattan on top of this section, letting the glue dry and harden for 5 minutes.^{[8]
X
Research source}
- Double-check the super glue tube for an exact drying recommendation.
Grab the loose end of the rattan material, threading it over and under the perpendicular sections of rattan along your furniture. Continue weaving the rattan strand until you’ve completely filled in the broken section.^{[9]
X
Research source}
Pull on the replacement rattan strand so it’s completely taut. Line up the excess strand so the end stretches to the center of the next perpendicular rattan section. Then, trim off any extra material with your pliers or scissors.^{[10]
X
Research source}
8
Apply a dot of glue and tuck the strand beneath the neighboring rattan material. Squeeze a dot of super glue onto the other end of the new strand. Then, tuck the rattan beneath the perpendicular section of material.^{[11]
X
Research source}
- You don’t need to hold the strand in place—it’ll stick to the material on its own.
To be safe, read over the label on your super glue to see how much time it needs to harden. Don’t sit on or use the furniture until the glue has enough time to dry, seal, and cure completely.^{[12]
X
Research source}