dsPIC33EV256GM002 PWM settings

Question

I developed a simple program to produce PWM waveform on dsPIC33EV256GM002 but I can't disable it. I used PWM1 and PWM2 and I would generate PWM waveform on PWM1L1 pin (pin 26 on DIP package) maintain PWM1H1 (pin 25 on DIP package) as digital I/O. Teorically the PWM register setting: IOCON1bits.PENL = 1; /* PWM1L is controlled by PWM module / IOCON1bits.PENH = 0; / PWM1H is controlled by GPIO module */ should do that but, using and oscilloscope, I noticed the PWM waveform on PWM1H1 pin, with opposite value (when PWM1L is 1 PWM1H is 0 and veceversa) even if it should be a digital I/O.

Did you find any similar problem ?

Thank you very much for your help and cooperation

regards

I used the following code:

TRISBbits.TRISB10 = 0;                  /* Set as a digital output */
TRISBbits.TRISB11 = 0;                  /* Set as a digital output */
TRISBbits.TRISB12 = 0;                  /* Set as a digital output */
TRISBbits.TRISB13 = 0;                  /* Set as a digital output */
TRISBbits.TRISB14 = 0;                  /* Set as a digital output */
TRISBbits.TRISB15 = 0;                  /* Set as a digital output */

LATBbits.LATB10 = 0;                /* Set as a digital output */
LATBbits.LATB11 = 0;                /* Set as a digital output */
LATBbits.LATB12 = 0;                /* Set as a digital output */
LATBbits.LATB13 = 0;                /* Set as a digital output */
LATBbits.LATB14 = 0;                /* Set as a digital output */
LATBbits.LATB15 = 0;                /* Set as a digital output */

  PORTBbits.RB10=0;
  PORTBbits.RB11=0;
  PORTBbits.RB12=0;
  PORTBbits.RB13=0;
  PORTBbits.RB14=0;
  PORTBbits.RB15=0;

  PTPER = 4000; 
/*~~~~~~~~~~ PWM1 Configuration ~~~~~~~~~~~~~~~~~~~~~~~~~~~~*/    
IOCON1bits.PENL      = 1;   /* PWM1L is controlled by PWM module */ 
IOCON1bits.PENH      = 0;   /* PWM1H is controlled by GPIO module */
IOCON1bits.PMOD      = 0;   /* Select Independent Output PWM mode */
PDC1 = 500;                 /* Initial Duty cycle */ 
DTR1    = 0;                /* Deadtime setting */
ALTDTR1 = 0;                /* Deadtime setting */
PHASE1 = 0;                 /* No phase shift */

/*~~~~~~~~~~~ PWM2 Configuration ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~*/
IOCON2bits.PENH      = 1;  /* PWM2H is controlled by PWM module */
IOCON2bits.PENL      = 0;  /* PWM2L is controlled by GPIO module */
IOCON2bits.PMOD      = 0;  /* Select Independent Output PWM mode */
PDC2 = 2000;               /* Initial Duty cycle */ 
DTR2    = 0;               /* Deadtime setting */
ALTDTR2 = 0;               /* Deadtime setting */
PHASE2 = 0;                /* */

PTCONbits.PTEN       = 1; /* Enable the PWM Module */

score 1 · Answer 1 · edited Apr 01 '19 at 18:10

1

I faced same problem with dspic33ev32GP002 and changed configuration bits like so:

// FDEVOPT
#pragma config PWMLOCK = OFF

This worked for me.

edited Apr 01 '19 at 18:10

Cody Gray

222,280
47
466
543

answered Dec 23 '15 at 13:08

user5711291

11
1

score 0 · Answer 2 · edited Apr 01 '19 at 18:10

0

The problem was related to the write protection of IOCONxbits register. I added the following line:

_FDEVOPT( PWMLOCK_OFF );

and this fixed the problem.

edited Apr 01 '19 at 18:10

Cody Gray

222,280
47
466
543

answered Jul 18 '15 at 18:51

Ferrari

55
1
9

dsPIC33EV256GM002 PWM settings

2 Answers2